Slot Number Invalid Bdo
Slot Number Invalid Bdo Rating: 6,3/10 9539 votes
14 is currently the max. You can pick up one character slot for free right now - its in pearl shop - loyalty tab. You can get character slots for loyalty and pearl shop aswell. I am not sure what is the starting amount - used to be around 4 I think. 1800-10-631-8000 (PLDT) 1800-3-631-8000 (Digitel) 1800-5-631-8000 (Bayantel) 1800-8-631-8000 (Globelines). The shop slot number is invalid. Technical Issues. I can't sell anything to NPCs anymore. This thread is archived.
Slot Number Invalid Bdo Contact
2013-09-16 00:07:21 UTC
Slot Number Invalid Bdo Card
Hello.
I have an LSI 9211-8i controller which is running the IR firmware. My
intention is to flash it with the IT firmware and use it for an md
RAID array.
However I don't think it is playing nicely with my motherboard BIOS.
On first installing it, with no drives attached, the LSI BIOS runs and
then the motherboard BIOS goes through an AHCI drive detection phase.
After detecting the drives (2xHD 1xOptical, connected to SATA ports on
MB) the boot hung and required a hard reset.
The LSI MPT2BIOS version is 7.29.0.0 and the controller firmware is 15.0.0.0-IR.
The motherboard is a Gigabyte GA-MA78G-DS3H (revision 1) running the F3 BIOS.
I can enter the LSI configuration utility during the controller boot
process and I see that it has a PCI slot of 'ff' which, according to
the utility, indicates an invalid PCI slot.
I've updated to the latest motherboard BIOS (F9) and now the boot
process follows the same sequence but continues after the AHCI
detection and eventually brings up linux. However the controller
still reports a PCI slot of 'ff'.
I can see it in linux but if I have a drive connected I don't see it
in the boot configuration utility (not sure if I should) and I don't
see it as a /dev/sd? device (not sure if this is where I should find
it). So I suspect it's not really working.
Here is the output from lspci -v:
02:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic
SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] (rev 03)
Subsystem: LSI Logic / Symbios Logic Device 3020
Flags: bus master, fast devsel, latency 0, IRQ 18
I/O ports at de00 [size=256]
Memory at fdcfc000 (64-bit, non-prefetchable) [size=16K]
Memory at fdc80000 (64-bit, non-prefetchable) [size=256K]
[virtual] Expansion ROM at fdb00000 [disabled] [size=512K]
Capabilities: [50] Power Management version 3
Capabilities: [68] Express Endpoint, MSI 00
Capabilities: [d0] Vital Product Data
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [c0] MSI-X: Enable+ Count=15 Masked-
Capabilities: [100] Advanced Error Reporting
Capabilities: [138] Power Budgeting <?>
Capabilities: [150] Single Root I/O Virtualization (SR-IOV)
Capabilities: [190] Alternative Routing-ID Interpretation (ARI)
Kernel driver in use: mpt2sas
Kernel modules: mpt2sas
Anybody run into this or have any advice? Is this really a problem?
I'm reluctant to risk bricking it during a firmware flash if it truly
is misbehaving.
Thanks.
--
To unsubscribe from this list: send the line 'unsubscribe linux-raid' in
the body of a message to ***@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
I have an LSI 9211-8i controller which is running the IR firmware. My
intention is to flash it with the IT firmware and use it for an md
RAID array.
However I don't think it is playing nicely with my motherboard BIOS.
On first installing it, with no drives attached, the LSI BIOS runs and
then the motherboard BIOS goes through an AHCI drive detection phase.
After detecting the drives (2xHD 1xOptical, connected to SATA ports on
MB) the boot hung and required a hard reset.
The LSI MPT2BIOS version is 7.29.0.0 and the controller firmware is 15.0.0.0-IR.
The motherboard is a Gigabyte GA-MA78G-DS3H (revision 1) running the F3 BIOS.
I can enter the LSI configuration utility during the controller boot
process and I see that it has a PCI slot of 'ff' which, according to
the utility, indicates an invalid PCI slot.
I've updated to the latest motherboard BIOS (F9) and now the boot
process follows the same sequence but continues after the AHCI
detection and eventually brings up linux. However the controller
still reports a PCI slot of 'ff'.
I can see it in linux but if I have a drive connected I don't see it
in the boot configuration utility (not sure if I should) and I don't
see it as a /dev/sd? device (not sure if this is where I should find
it). So I suspect it's not really working.
Here is the output from lspci -v:
02:00.0 Serial Attached SCSI controller: LSI Logic / Symbios Logic
SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] (rev 03)
Subsystem: LSI Logic / Symbios Logic Device 3020
Flags: bus master, fast devsel, latency 0, IRQ 18
I/O ports at de00 [size=256]
Memory at fdcfc000 (64-bit, non-prefetchable) [size=16K]
Memory at fdc80000 (64-bit, non-prefetchable) [size=256K]
[virtual] Expansion ROM at fdb00000 [disabled] [size=512K]
Capabilities: [50] Power Management version 3
Capabilities: [68] Express Endpoint, MSI 00
Capabilities: [d0] Vital Product Data
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [c0] MSI-X: Enable+ Count=15 Masked-
Capabilities: [100] Advanced Error Reporting
Capabilities: [138] Power Budgeting <?>
Capabilities: [150] Single Root I/O Virtualization (SR-IOV)
Capabilities: [190] Alternative Routing-ID Interpretation (ARI)
Kernel driver in use: mpt2sas
Kernel modules: mpt2sas
Anybody run into this or have any advice? Is this really a problem?
I'm reluctant to risk bricking it during a firmware flash if it truly
is misbehaving.
Thanks.
--
To unsubscribe from this list: send the line 'unsubscribe linux-raid' in
the body of a message to ***@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html